Multiple BMP in Series — Equations
System case
Case type: Retention in Series. Calculation used: Retention in Series (one combined retention system).
Retention system (2 retention BMPs as one) [BMP 1 (Permeable Pavement) + BMP 2 (Retention)]
| Segment | BMPs | How it is calculated |
| Retention system (2 retention BMPs as one) | BMP 1 (Permeable Pavement) + BMP 2 (Retention) | Treatment depths summed (Equivalent Treatment Depth); removal e from the retention lookup tables; e is the Multiple BMP's removal |
Equations
Equivalent Treatment Depth (in) = sum of the Treatment Depths of the retention BMPs
Equivalent Treatment Efficiency e (%) = retention lookup (Equivalent Treatment Depth, non-DCIA CN, DCIA %, rainfall zone)
N removal = P removal = Hydraulic Capture = e
Notes
- The Multiple BMP detects its scenario from the BMPs in the series and uses the calculation named above.
- The steps table lists every calculation in the order it was made, with the values used.
- Each BMP's section shows its own equations and its values as they stand after the series calculation.
- When all upstream BMPs consist of Retention BMPs, the sum of the treatment depths are used to calculate efficiency. These are titled Equivalent Treatment Depth and Equivalent Treatment Efficiency.
- There is no downstream BMP in this series, so this efficiency is also the treatment efficiency of the Multiple BMP.
Values
| Variable | Current value |
| Scenario | Retention in Series |
| Calculation used | Retention in Series (one combined retention system) |
| Runoff into the series | 13.903 ac-ft/yr |
| N load into the series | 21.428 kg/yr |
| P load into the series | 2.966 kg/yr |
| Equivalent Treatment Depth | 1.411 in |
| Equivalent Treatment Efficiency (e) | 78.908 % |
| Hydraulic Capture | 78.9 % |
| N removal (Multiple BMP) | 78.9 % |
| P removal (Multiple BMP) | 78.9 % |
| N load out (surface discharge) | 4.52 kg/yr |
| P load out (surface discharge) | 0.626 kg/yr |
Calculation steps (values as used)
| # | Step | Calculation (values used) | Result |
| 1 | Inflow to the series | catchment runoff and loads | Q 13.903 ac-ft/yr, N 21.428 kg/yr, P 2.966 kg/yr |
| 2 | Equivalent Treatment Depth | BMP 1 (Permeable Pavement) 0.66 in + BMP 2 (Retention) 0.751 in | 1.411 in |
| 3 | Equivalent Treatment Efficiency (e) | retention lookup at 1.411 in, non-DCIA CN 80, DCIA 60 %, Florida Zone 5 | 78.91 % |
| 4 | Multiple BMP removal | N = P = Hydraulic Capture = e | 78.91 % |
BMP 1: Permeable Pavement
Part of the combined retention system: its Treatment Depth is added into the Equivalent Treatment Depth. Its own N and P removal below is not applied separately.
Equations
Storage (ac-ft) = Surface Area (ac) x Sum over layers [Layer Thickness (in) x Sustainable Void (%) / 100] x Layer Scale Factor / 12
Treatment Depth (in) = Storage / Watershed Area (ac) x 12
Notes
- Sizing scales every pavement layer by the same factor: 1.0 is the layers as entered, 1.5 makes each layer half again as thick. Apply multiplies each layer thickness by the factor; Cancel leaves the layers as they were.
- With no layers entered, sizing starts from 12 in of User Defined(20).
- Hydraulic capture efficiency is read from the retention efficiency lookup tables for the Treatment Depth.
- The lookup also depends on the watershed's non-DCIA curve number, DCIA percent and rainfall zone.
- N and P removal are equal to the hydraulic capture efficiency.
- A recovery-time adjustment for Time to Recover Design Volume is added to the capture efficiency and to N and P removal (see Recovery-Time Adjustment).
Values
| Variable | Current value |
| Contributing Area | 4.000 ac |
| Watershed Area | 5.000 ac |
| Non-DCIA Curve Number | 80 |
| DCIA Percent | 60 % |
| Rainfall Zone | Florida Zone 5 |
| Treatment Depth | 0.660 in |
| Hydraulic Capture | 57.9 % |
| Treatment Rate | (no media mix) |
| N removal | 57.9 % |
| P removal | 57.9 % |
Recovery-Time Adjustment
The efficiency from the retention lookup tables is raised by an adjustment that depends on the Treatment Depth and on how quickly the design volume is recovered.
Equations
x = Treatment Depth (in), T = Time to Recover Design Volume (hr)
T <= 3 hr: Adjustment (%) = -0.1365 x^4 + 1.5228 x^3 - 5.0475 x^2 + 2.3674 x + 8.8133
3 < T <= 36 hr: Adjustment (%) = 0.0083 x^4 - 0.1518 x^3 + 1.0071 x^2 - 3.0705 x + 3.7676
Hydraulic Capture (%) = Lookup Table Capture (%) + Adjustment
N removal (%) = P removal (%) = Lookup Table Capture (%) + Adjustment
Notes
- No adjustment is made when T is not entered (0) or is greater than 36 hours.
- A negative adjustment is set to 0.
- N and P removal cannot exceed 100%.
| Variable | Current value |
| Time to Recover Design Volume (T) | 72 hr |
| Treatment Depth (x) | 0.660 in |
| Curve used | T > 36 hr: no adjustment |
| Recovery Time Adjustment | 0.00 % |
BMP 2: Retention
Part of the combined retention system: its Treatment Depth is added into the Equivalent Treatment Depth. Its own N and P removal below is not applied separately.
Equations
Treatment Depth (in) = Retention Volume (ac-ft) / Contributing Area (ac) x 12
Notes
- Hydraulic capture efficiency is read from the retention efficiency lookup tables for the Treatment Depth.
- The lookup also depends on the watershed's non-DCIA curve number, DCIA percent and rainfall zone.
- N and P removal are equal to the hydraulic capture efficiency.
- A recovery-time adjustment for Time to Recover Design Volume is added to the capture efficiency and to N and P removal (see Recovery-Time Adjustment).
Values
| Variable | Current value |
| Retention Volume | 0.313 ac-ft |
| Contributing Area | 5.000 ac |
| Watershed Area | 5.000 ac |
| Non-DCIA Curve Number | 80 |
| DCIA Percent | 60 % |
| Rainfall Zone | Florida Zone 5 |
| Treatment Depth | 0.751 in |
| Hydraulic Capture | 62.1 % |
| Treatment Rate | (no media mix) |
| N removal | 62.1 % |
| P removal | 62.1 % |
Recovery-Time Adjustment
The efficiency from the retention lookup tables is raised by an adjustment that depends on the Treatment Depth and on how quickly the design volume is recovered.
Equations
x = Treatment Depth (in), T = Time to Recover Design Volume (hr)
T <= 3 hr: Adjustment (%) = -0.1365 x^4 + 1.5228 x^3 - 5.0475 x^2 + 2.3674 x + 8.8133
3 < T <= 36 hr: Adjustment (%) = 0.0083 x^4 - 0.1518 x^3 + 1.0071 x^2 - 3.0705 x + 3.7676
Hydraulic Capture (%) = Lookup Table Capture (%) + Adjustment
N removal (%) = P removal (%) = Lookup Table Capture (%) + Adjustment
Notes
- No adjustment is made when T is not entered (0) or is greater than 36 hours.
- A negative adjustment is set to 0.
- N and P removal cannot exceed 100%.
| Variable | Current value |
| Time to Recover Design Volume (T) | 72 hr |
| Treatment Depth (x) | 0.751 in |
| Curve used | T > 36 hr: no adjustment |
| Recovery Time Adjustment | 0.00 % |