How this treatment's values are worked out: the equations, then the values they are worked with (v1's Equations button). A change on the Entry or Sizing tab shows here at once.
Case type: Retention in Series. Calculation used: Retention in Series (one combined retention system).
Retention system (2 retention BMPs as one) [BMP 1 (Permeable Pavement) + BMP 2 (Retention)]
| Segment | BMPs | How it is calculated |
|---|---|---|
| Retention system (2 retention BMPs as one) | BMP 1 (Permeable Pavement) + BMP 2 (Retention) | Treatment depths summed (Equivalent Treatment Depth); removal e from the retention lookup tables; e is the Multiple BMP's removal |
Equivalent Treatment Depth (in) = sum of the Treatment Depths of the retention BMPs
Equivalent Treatment Efficiency e (%) = retention lookup (Equivalent Treatment Depth, non-DCIA CN, DCIA %, rainfall zone)
N removal = P removal = Hydraulic Capture = e
The Multiple BMP detects its scenario from the BMPs in the series and uses the calculation named above.
The steps table lists every calculation in the order it was made, with the values used.
Each BMP's section shows its own equations and its values as they stand after the series calculation.
When all upstream BMPs consist of Retention BMPs, the sum of the treatment depths are used to calculate efficiency. These are titled Equivalent Treatment Depth and Equivalent Treatment Efficiency.
There is no downstream BMP in this series, so this efficiency is also the treatment efficiency of the Multiple BMP.
| Variable | Current value |
|---|---|
| Scenario | Retention in Series |
| Calculation used | Retention in Series (one combined retention system) |
| Runoff into the series | 13.903 ac-ft/yr |
| N load into the series | 21.428 kg/yr |
| P load into the series | 2.966 kg/yr |
| Equivalent Treatment Depth | 1.411 in |
| Equivalent Treatment Efficiency (e) | 78.908 % |
| Hydraulic Capture | 78.9 % |
| N removal (Multiple BMP) | 78.9 % |
| P removal (Multiple BMP) | 78.9 % |
| N load out (surface discharge) | 4.5 kg/yr |
| P load out (surface discharge) | 0.623 kg/yr |
| # | Step | Calculation (values used) | Result |
|---|---|---|---|
| 1 | Inflow to the series | catchment runoff and loads | Q 13.903 ac-ft/yr, N 21.428 kg/yr, P 2.966 kg/yr |
| 2 | Equivalent Treatment Depth | BMP 1 (Permeable Pavement) 0.66 in + BMP 2 (Retention) 0.751 in | 1.411 in |
| 3 | Equivalent Treatment Efficiency (e) | retention lookup at 1.411 in, non-DCIA CN 80, DCIA 60 %, Florida Zone 5 | 78.91 % |
| 4 | Multiple BMP removal | N = P = Hydraulic Capture = e | 78.91 % |
Part of the combined retention system: its Treatment Depth is added into the Equivalent Treatment Depth. Its own N and P removal below is not applied separately.
Equations
Storage (ac-ft) = Surface Area (ac) x Sum over layers [Layer Thickness (in) x Sustainable Void (%) / 100] x Layer Scale Factor / 12
Treatment Depth (in) = Storage / Watershed Area (ac) x 12
Notes
Sizing scales every pavement layer by the same factor: 1.0 is the layers as entered, 1.5 makes each layer half again as thick. Apply multiplies each layer thickness by the factor; Cancel leaves the layers as they were.
With no layers entered, sizing starts from 12 in of User Defined(20).
Hydraulic capture efficiency is read from the retention efficiency lookup tables for the Treatment Depth.
The lookup also depends on the watershed's non-DCIA curve number, DCIA percent and rainfall zone.
N and P removal are equal to the hydraulic capture efficiency.
A recovery-time adjustment for Time to Recover Design Volume is added to the capture efficiency and to N and P removal (see Recovery-Time Adjustment).
Values
| Variable | Current value |
|---|---|
| Contributing Area | 4.000 ac |
| Watershed Area | 5.000 ac |
| Non-DCIA Curve Number | 80 |
| DCIA Percent | 60 % |
| Rainfall Zone | Florida Zone 5 |
| Treatment Depth | 0.660 in |
| Hydraulic Capture | 57.9 % |
| Treatment Rate | (no media mix) |
| N removal | 57.9 % |
| P removal | 57.9 % |
Part of the combined retention system: its Treatment Depth is added into the Equivalent Treatment Depth. Its own N and P removal below is not applied separately.
Equations
Treatment Depth (in) = Retention Volume (ac-ft) / Contributing Area (ac) x 12
Notes
Hydraulic capture efficiency is read from the retention efficiency lookup tables for the Treatment Depth.
The lookup also depends on the watershed's non-DCIA curve number, DCIA percent and rainfall zone.
N and P removal are equal to the hydraulic capture efficiency.
Values
| Variable | Current value |
|---|---|
| Retention Volume | 0.313 ac-ft |
| Contributing Area | 5.000 ac |
| Watershed Area | 5.000 ac |
| Non-DCIA Curve Number | 80 |
| DCIA Percent | 60 % |
| Rainfall Zone | Florida Zone 5 |
| Treatment Depth | 0.751 in |
| Hydraulic Capture | 62.1 % |
| Treatment Rate | (no media mix) |
| N removal | 62.1 % |
| P removal | 62.1 % |