SoftwarePlus.ai

All programs › BMPFast › Sample problems

Swale with groundwater discharge (sample project)

BMPFast sample project example problem 1: a roadside swale.

1The problem

The BMPFast sample project example problem 1 swale ground water discharge: a roadside swale treats the runoff of the road and its shoulders.

InputValueSource
Project (General Site Information)
Meteorological zoneFlorida Zone 1Zone map (help page 815)
Mean annual rainfall60 inMean annual rainfall map (help page 815)
Performance standard (analysis type)Net ImprovementBMPFast sample project
Catchment 1: roadside (Watershed Characteristics)
Land use, pre / postAgricultural - Pasture / HighwayBMPFast sample project
Area, pre / post1.2 / 1.2 acBMPFast sample project
Non-DCIA curve number, pre / post80 / 85BMPFast sample project
DCIA, pre / post0 / 60 %BMPFast sample project
EMC TN, pre / post3.030 / 1.250 mg/LBMPFast land use table (AH Vol I Table 9.2)
EMC TP, pre / post0.593 / 0.173 mg/LBMPFast land use table (AH Vol I Table 9.2)
Swale (worksheet)
Swale top width for flood conditions [W]10 ftBMPFast sample project
Swale bottom width [B]0 ftBMPFast sample project
Swale length [L]871.2 ftBMPFast sample project
Average catchment length871.2 ftBMPFast sample project
Average impervious width (including shoulder)20 ftBMPFast sample project
Average width of pervious area including swale40 ftBMPFast sample project
Swale slope [S]0.001 ft/ftBMPFast sample project
Manning's n0.05BMPFast sample project
Soil infiltration rate2.5 in/hrBMPFast sample project
Side slope [Z]5 H:VBMPFast sample project
Average height of the swale blocks [H]0 ftBMPFast sample project
Length of the berm upstream of the crest0 ftBMPFast sample project
Number of swale blocks0BMPFast sample project

Find: the TN and TP removal of the BMP, the loads leaving the site, and whether the performance standard is met.

2Steps in BMPFast

  1. Press Open Project and open swale-groundwater.bmpt (the file under Files; it is the BMPFast sample project example problem 1 swale ground water discharge.bmpt). General Site Information (the main window; its title bar reads General Site Information and your license key) shows Florida Zone 1, 60.0 in of rainfall and the performance standard Net Improvement.

    General Site Information (the main window).
    General Site Information (the main window).
  2. Press 1. Enter Catchment. For Catchment 1 type the name roadside , choose the land uses Agricultural - Pasture (pre) and Highway (post), enter the areas 1.2 and 1.2 ac, the non-DCIA curve numbers 80 and 85 and the DCIA 0 and 60 %, then press Calculate. BMPFast shows the annual runoff coefficient, the runoff and the TN and TP loads. Press Back.

    Watershed Characteristics Worksheet (1. Enter Catchment).
    Watershed Characteristics Worksheet (1. Enter Catchment).
  3. Press 2. Enter Treatment and then Swale. On the Swale worksheet: Swale top width for flood conditions [W] 10 ft; Swale bottom width [B] 0 ft; Swale length [L] 871.2 ft; Average catchment length 871.2 ft; Average impervious width (including shoulder) 20 ft; Average width of pervious area including swale 40 ft; Swale slope [S] 0.001 ft/ft; Manning's n 0.05; Soil infiltration rate 2.5 in/hr; Side slope [Z] 5 H:V; Average height of the swale blocks [H] 0 ft; Length of the berm upstream of the crest 0 ft; Number of swale blocks 0. Press Calculate. The report on the worksheet shows the inputs and the results.

    The BMP worksheet after Calculate: the report on the left.
    The BMP worksheet after Calculate: the report on the left.
  4. Press the same button again, now labelled Equations: the worksheet shows each equation with this problem’s values. Press Back to return to the treatment options.

    The same worksheet showing Equations: each equation with this problem’s values.
    The same worksheet showing Equations: each equation with this problem’s values.
  5. On the main window press 3. Configure Catchments and double-click Catchment 1. Choose Swale as the BMP used in routing and the Outlet as where it goes. Press Back twice. (A catchment’s BMP is only used once it is chosen here.)

    Routing for Catchment 1 (3. Configure Catchments): the BMP used and where the catchment goes.
    Routing for Catchment 1 (3. Configure Catchments): the BMP used and where the catchment goes.
  6. Press 4. Summary Report. The Report Viewer shows the loads, the removal and whether the performance standard is met. Press Save Project to keep your copy; compare it with the .bmpt under Files.

    The Summary Report (4. Summary Report) in the Report Viewer.
    The Summary Report (4. Summary Report) in the Report Viewer.

3Results

ResultValue
Catchment 1: computed by BMPFast
Annual runoff coefficient (ROC), pre / post0.162 / 0.598
Runoff, pre / post0.972 / 3.588 ac-ft/yr
TN load, pre / post3.631 / 5.530 kg/yr
TP load, pre / post0.711 / 0.765 kg/yr
Swale: computed by BMPFast
Treatment depth0.396 in
Hydraulic capture efficiency38.85 %
Provided TN / TP removal38.85 % / 38.85 %
TN load in → out5.530 → 3.382 kg/yr
TP load in → out0.765 → 0.468 kg/yr
Site (all catchments, at the outlet)
TN load: catchments → outlet5.530 → 3.382 kg/yr
TP load: catchments → outlet0.765 → 0.468 kg/yr
Provided removal TN / TP38.8 % / 38.8 %
Required removal TN / TP (Maximum % Removal)34.3 % (met) / 7.1 % (met)

The BMP report

Open this report on its own page.

The Summary Report

Open this report on its own page.

4Check

Runoff and loads (Equations 9-1 and 9-2 of AH Vol I).

1.233 kg is 1 mg/L in 1 ac-ft.

Infiltration. With no swale blocks the treatment depth is the depth infiltrated along the swale: 0.3959 in (program treatment depth 0.3959; the Equations page shows the Manning and infiltration steps).

Capture. The retention efficiency tables for Florida Zone 1 at a treatment depth of 0.396 in, non-DCIA CN 85.00 and DCIA 60.0 % give a hydraulic capture of 38.85 % (AH Vol I Appendix O; read the same tables with Tools › Retention Efficiency Lookup Tables, help page 4325). A swale is a retention BMP: the removal equals the capture.

Load out.

The program’s Equations page

Open this report on its own page.

5Files

6Help and methodology

Calculated with BMPFast 1.1.9 (build 6.0.0, 2026-10-16). Older versions may not have the Equations button or may give slightly different results; download the latest at bmpfast.com. Screen captures are for demonstration only.