All programs › BMPFast › Sample problems
Swale with groundwater discharge (sample project)
BMPFast sample project example problem 1: a roadside swale.
Help: Swale (help page 324) · Download the .bmpt · Link to Solution in BMPFast Version 2
1The problem
The BMPFast sample project example problem 1 swale ground water discharge: a roadside swale treats the runoff of the road and its shoulders.
| Input | Value | Source |
|---|---|---|
| Project (General Site Information) | ||
| Meteorological zone | Florida Zone 1 | Zone map (help page 815) |
| Mean annual rainfall | 60 in | Mean annual rainfall map (help page 815) |
| Performance standard (analysis type) | Net Improvement | BMPFast sample project |
| Catchment 1: roadside (Watershed Characteristics) | ||
| Land use, pre / post | Agricultural - Pasture / Highway | BMPFast sample project |
| Area, pre / post | 1.2 / 1.2 ac | BMPFast sample project |
| Non-DCIA curve number, pre / post | 80 / 85 | BMPFast sample project |
| DCIA, pre / post | 0 / 60 % | BMPFast sample project |
| EMC TN, pre / post | 3.030 / 1.250 mg/L | BMPFast land use table (AH Vol I Table 9.2) |
| EMC TP, pre / post | 0.593 / 0.173 mg/L | BMPFast land use table (AH Vol I Table 9.2) |
| Swale (worksheet) | ||
| Swale top width for flood conditions [W] | 10 ft | BMPFast sample project |
| Swale bottom width [B] | 0 ft | BMPFast sample project |
| Swale length [L] | 871.2 ft | BMPFast sample project |
| Average catchment length | 871.2 ft | BMPFast sample project |
| Average impervious width (including shoulder) | 20 ft | BMPFast sample project |
| Average width of pervious area including swale | 40 ft | BMPFast sample project |
| Swale slope [S] | 0.001 ft/ft | BMPFast sample project |
| Manning's n | 0.05 | BMPFast sample project |
| Soil infiltration rate | 2.5 in/hr | BMPFast sample project |
| Side slope [Z] | 5 H:V | BMPFast sample project |
| Average height of the swale blocks [H] | 0 ft | BMPFast sample project |
| Length of the berm upstream of the crest | 0 ft | BMPFast sample project |
| Number of swale blocks | 0 | BMPFast sample project |
Find: the TN and TP removal of the BMP, the loads leaving the site, and whether the performance standard is met.
2Steps in BMPFast
Press Open Project and open
swale-groundwater.bmpt(the file under Files; it is the BMPFast sample project example problem 1 swale ground water discharge.bmpt). General Site Information (the main window; its title bar reads General Site Information and your license key) shows Florida Zone 1, 60.0 in of rainfall and the performance standard Net Improvement.
General Site Information (the main window). Press 1. Enter Catchment. For Catchment 1 type the name roadside , choose the land uses Agricultural - Pasture (pre) and Highway (post), enter the areas 1.2 and 1.2 ac, the non-DCIA curve numbers 80 and 85 and the DCIA 0 and 60 %, then press Calculate. BMPFast shows the annual runoff coefficient, the runoff and the TN and TP loads. Press Back.

Watershed Characteristics Worksheet (1. Enter Catchment). Press 2. Enter Treatment and then Swale. On the Swale worksheet: Swale top width for flood conditions [W] 10 ft; Swale bottom width [B] 0 ft; Swale length [L] 871.2 ft; Average catchment length 871.2 ft; Average impervious width (including shoulder) 20 ft; Average width of pervious area including swale 40 ft; Swale slope [S] 0.001 ft/ft; Manning's n 0.05; Soil infiltration rate 2.5 in/hr; Side slope [Z] 5 H:V; Average height of the swale blocks [H] 0 ft; Length of the berm upstream of the crest 0 ft; Number of swale blocks 0. Press Calculate. The report on the worksheet shows the inputs and the results.

The BMP worksheet after Calculate: the report on the left. Press the same button again, now labelled Equations: the worksheet shows each equation with this problem’s values. Press Back to return to the treatment options.

The same worksheet showing Equations: each equation with this problem’s values. On the main window press 3. Configure Catchments and double-click Catchment 1. Choose Swale as the BMP used in routing and the Outlet as where it goes. Press Back twice. (A catchment’s BMP is only used once it is chosen here.)

Routing for Catchment 1 (3. Configure Catchments): the BMP used and where the catchment goes. Press 4. Summary Report. The Report Viewer shows the loads, the removal and whether the performance standard is met. Press Save Project to keep your copy; compare it with the .bmpt under Files.

The Summary Report (4. Summary Report) in the Report Viewer.
3Results
| Result | Value |
|---|---|
| Catchment 1: computed by BMPFast | |
| Annual runoff coefficient (ROC), pre / post | 0.162 / 0.598 |
| Runoff, pre / post | 0.972 / 3.588 ac-ft/yr |
| TN load, pre / post | 3.631 / 5.530 kg/yr |
| TP load, pre / post | 0.711 / 0.765 kg/yr |
| Swale: computed by BMPFast | |
| Treatment depth | 0.396 in |
| Hydraulic capture efficiency | 38.85 % |
| Provided TN / TP removal | 38.85 % / 38.85 % |
| TN load in → out | 5.530 → 3.382 kg/yr |
| TP load in → out | 0.765 → 0.468 kg/yr |
| Site (all catchments, at the outlet) | |
| TN load: catchments → outlet | 5.530 → 3.382 kg/yr |
| TP load: catchments → outlet | 0.765 → 0.468 kg/yr |
| Provided removal TN / TP | 38.8 % / 38.8 % |
| Required removal TN / TP (Maximum % Removal) | 34.3 % (met) / 7.1 % (met) |
The BMP report
Open this report on its own page.
The Summary Report
4Check
Runoff and loads (Equations 9-1 and 9-2 of AH Vol I).
| Runoff | = ROC × area × rainfall / 12 |
| = 0.598 × 1.20 ac × 60.0 in / 12 | |
| = 3.588 ac-ft/yr (program 3.588). |
| TN load | = EMC × runoff × 1.233 |
| = 1.250 × 3.588 × 1.233 | |
| = 5.530 kg/yr (program 5.530) |
| TP load | = 0.173 × 3.588 × 1.233 |
| = 0.765 kg/yr (program 0.765). |
1.233 kg is 1 mg/L in 1 ac-ft.
| Rainfall excess area | = (W × L + impervious L × impervious W) / 43,560 |
| = (10 × 871 + 871 × 20) / 43,560 | |
| = 0.6000 ac (program 0.6000). |
Infiltration. With no swale blocks the treatment depth is the depth infiltrated along the swale: 0.3959 in (program treatment depth 0.3959; the Equations page shows the Manning and infiltration steps).
Capture. The retention efficiency tables for Florida Zone 1 at a treatment depth of 0.396 in, non-DCIA CN 85.00 and DCIA 60.0 % give a hydraulic capture of 38.85 % (AH Vol I Appendix O; read the same tables with Tools › Retention Efficiency Lookup Tables, help page 4325). A swale is a retention BMP: the removal equals the capture.
Load out.
| TN out | = load in × (1 − removal) |
| = 5.530 × (1 − 38.85 / 100) | |
| = 3.382 kg/yr (program 3.382) |
| TP out | = 0.765 × (1 − 38.85 / 100) |
| = 0.468 kg/yr (program 0.468). |
The program’s Equations page
5Files
- swale-groundwater.bmpt: the project, saved by BMPFast. Save it (your browser puts it in Downloads). In BMPFast press Open Project, then Open Project again in the Open BMPFast Project dialog (below its Recent Projects list), and choose the file.
- Equations page (worksheet) (as BMPFast shows it)
- Summary Report (as BMPFast shows it)
- BMP report (worksheet) (as BMPFast shows it)
6Help and methodology
Calculated with BMPFast 1.1.9 (build 6.0.0, 2026-10-16). Older versions may not have the Equations button or may give slightly different results; download the latest at bmpfast.com. Screen captures are for demonstration only.