SoftwarePlus.ai

All programs › BMPFast › Help

Retention BMPs

A copy of the help on bmpfast.com (last changed there 2026-10-20; copied here 2026-10-21). These pages describe the windows of BMPFast (version 1). BMPFast 2 uses the same methods; its numbered buttons are the tree on the left: General Site Information, then Catchments with their Treatments, Catchment Routings and Calculators.

BMPFast treats a BMP as retention when its removal comes from the retention curves. The BMP’s storage is turned into a Treatment Depth: the inches of runoff it holds over the area that drains to it. The program then reads that depth on the retention curves for the catchment’s Non-DCIA Curve Number, DCIA percent and meteorological zone. The curves themselves are explained on Retention Methodology. This page covers the step before them: how each BMP calculates its Treatment Depth.

The common steps

  1. Storage. The BMP’s storage volume, from its dimensions (each BMP below). The worksheet’s report shows it as the Treatment Volume (ac-ft) beside the Treatment Depth; the routing uses it (below).
  2. Treatment Depth. Treatment Depth (in) = 12 × Storage (ac-ft) / Area (ac). Which area is used depends on the BMP: the contributing area (the catchment without the BMP’s own footprint) or the whole watershed area of the catchment. The table below says which.
  3. Capture. Hydraulic Capture (%) = the retention curves at that Treatment Depth, with the catchment’s post-development Non-DCIA CN and DCIA percent (Catchment Characteristics) and the project’s zone. Depths above 4 in are read at 4 in (Retention Methodology).
  4. Removal. Nitrogen and phosphorus removal equal the capture, because the retained water keeps its load. Some BMPs then add to it, as the table shows. Removal is never more than 100 %.

Applicant’s Handbook reference

Section 2.0 Definitions and Terms, “Retention”: a system “designed to prevent the discharge of a given volume of stormwater runoff into surface waters in the state by complete on-site storage”, for example depression storage areas or “pervious pavement with subgrade”; BMPFast gives every BMP on this page its removal from the storage it holds.

Appendix O, Dry Retention Systems: the retained volume is expressed as inches over the catchment area and read on the Appendix O tables; BMPFast does this with the Treatment Depth, spread over the contributing area or the watershed area as the table below says.

Appendix O, Green Stormwater Infrastructure: GSI and LID “can also treat stormwater similar to a traditional BMP by treating TN and TP as a retention system”, and Table 1 (BMP Efficiencies) says to “Use appropriate retention or detention calculation for volume captured then add an additional removal based on plant, soil and media selections in a treatment train configuration”; the “After the curves” column is that additional removal.

BMPStorageDivided byAfter the curves
RetentionProvided Retention VolumeContributing areaRecovery-Time Adjustment
ExfiltrationPipe and trench voidsContributing areaRecovery-Time Adjustment
Permeable PavementVoids in the pavement layersWatershed areaRecovery-Time Adjustment
Rain Garden (Retention)Media voids + water above the mediaContributing areaCredit for Native Soil and Cover Crop
Tree WellWell volume, all wellsWatershed areaRetention: none. Detention: × media reduction
SwaleInfiltration along the swale + swale blocksRainfall excess areaNone
Vegetated Natural Buffer (Retention)Soil storage in the bufferBuffer width + feeding width (a depth per foot of length)None
Vegetated Filter Strip (Retention)Soil storage in the stripStrip width + feeding width (a depth per foot of length)None

The Recovery-Time Adjustment raises the removal of a Retention, Exfiltration or Permeable Pavement BMP that recovers its design volume within 36 hours. It depends on the Treatment Depth and the Time to Recover Design Volume; the equations are on the Retention page. The other BMPs do not use it.

Applicant’s Handbook reference

Appendix O, Dry Retention Systems: the tables assume the treatment volume is recovered within 72 hours; BMPFast differs: the Recovery-Time Adjustment raises the removal for recovery within 36 hours, which the handbook does not provide for.

Source reference

BMPFast method (Storage.CalculateRecoveryDesignTimeAdjustment, Storage.cs; on the Equations page since 2026-10-02): the two polynomials for a recovery time of 3 hours or less and of 3 to 36 hours are BMPFast’s; the program does not give the study they were fitted to, and the retention tables themselves assume a 72-hour recovery.

Treatment Depth for each BMP

The equations are the ones each BMP’s worksheet uses. Its Equations page (the Calculate button, then Equations) shows them with the project’s own numbers.

Retention

Treatment Depth (in) = 12 × Provided Retention Volume (ac-ft) / Contributing Area (ac)

The retention basin holds and recovers the volume by infiltration. Worksheet: Retention.

Exfiltration

Pipe Volume (cf)   = π × (Pipe Span / 24) × (Pipe Rise / 24) × Pipe Length
Trench Volume (cf) = (Trench Width × Trench Depth × Trench Length − Pipe Volume) × Void Ratio
Storage (ac-ft) = (Pipe Volume + Trench Volume) / 43,560
Treatment Depth (in) = 12 × Storage / Contributing Area (ac)

Pipe span and rise are in inches; the other dimensions in feet. The storage is the inside of the pipe plus the voids of the aggregate around it. Worksheet: Exfiltration.

Applicant’s Handbook reference

Appendix O, Dry Retention Systems: the handbook has no heading for exfiltration trenches; BMPFast treats the pipe and trench storage as a dry retention volume, as Section 2.0 “Retention” (complete on-site storage) allows.

Permeable Pavement

Layer Storage (ac-ft) = Surface Area (ac) × Layer Thickness (in) × Layer Void (%) / 100 / 12
Storage (ac-ft) = sum of the Layer Storage of every layer
Treatment Depth (in) = 12 × Storage / Watershed Area (ac)

Unlike Retention and Exfiltration, the depth is spread over the whole catchment (watershed) area, pavement included. Worksheet: Permeable Pavement.

Applicant’s Handbook reference

Appendix O, Pervious pavement: “The nutrient reduction capability of these systems can be calculated in the same way as Dry Retention System”; BMPFast reads the pavement’s storage depth on the retention curves.

Rain Garden (Retention)

Storage (cf)         = Void Fraction × Media Volume (cf) + Water Above Media (cf)
Treatment Depth (in) = 12 × Storage / (43,560 × Contributing Area (ac))
N removal (%) = P removal (%) = Capture + Credit for Native Soil and Cover Crop / 100 × (100 − Capture)

The credit adds removal on the part of the runoff the storage does not capture. A rain garden set to Detention does not use the retention curves. Worksheet: Rain Garden.

Applicant’s Handbook reference

Appendix O, Raingarden/Bioretention Cell: “calculated in the same way as Dry Retention System”; BMPFast reads the storage depth on the retention curves.

Appendix O, Table 1 (BMP Efficiencies), Green Stormwater Infrastructure Efforts: an additional removal for plant, soil and media is added “in a treatment train configuration”; BMPFast applies the Credit for Native Soil and Cover Crop to the runoff the storage does not capture.

Tree Well

Storage per well (ac-ft) = Length × Width × (Depth + Soil Storage Capacity) / 43,560
Storage (ac-ft) = Storage per well × Number of Similar Areas
Treatment Depth (in) = 12 × Storage / Watershed Area (ac)
Retention: N removal (%) = P removal (%) = Capture
Detention: N removal (%) = Capture × Media N Reduction (%) / 100 (P the same with the P reduction)

Source reference

BMPFast method (TreeWell.cs, about line 130): the storage of a well is Length × Width × (Depth + Soil Storage Capacity); the sum adds a depth in feet to a storage fraction, and the program gives no source for it.

Worksheet: Tree Well.

Applicant’s Handbook reference

Appendix O, Tree Well: “calculated in the same way as Dry Retention System”; BMPFast reads the wells’ storage depth on the retention curves, and for Detention multiplies the capture by the media reduction, the media removal that Table 1 (BMP Efficiencies) allows for Tree wells.

Swale

Rainfall Excess Area (ac) = (W × L + Impervious L × Impervious W) / 43,560
Infiltrated Depth (in) = runoff infiltrated along the swale while it flows (Manning flow depth, wetted perimeter, infiltration rate)
Block Depth (in) = 12 × Swale Block Storage (cf) / (Rainfall Excess Area × 43,560)
Treatment Depth (in) = min(4, Infiltrated Depth + Block Depth)
Treatment Volume (ac-ft) = Treatment Depth × Rainfall Excess Area / 12

A swale’s depth has two parts: what soaks in along the swale as the runoff flows, and what the swale blocks (check dams) hold back. The full equations are on Swale.

Applicant’s Handbook reference

Appendix O, Swale: “Swales are online retention systems and their treatment effectiveness is directly related to the amount of the annual stormwater volume that is infiltrated”, with or without swale blocks, and are “calculated in the same way as Dry Retention System”; BMPFast turns the infiltrated volume and the block storage into a Treatment Depth on the retention curves.

Source reference

Wanielista, M.P., Yousef, Y.A. and Avellaneda, E. (1988). Alternatives for the Treatment of Groundwater Contaminants: Infiltration Capacity of Roadside Swales. Report FL-ER-38-88, FDOT and University of Central Florida, Chapter V and Appendix A (link): the infiltration along a flowing swale, from Manning’s equation and the soil’s infiltration rate, which BMPFast turns into the swale’s infiltrated depth.

Vegetated Natural Buffer and Vegetated Filter Strip (Retention)

Treatment Volume (ac-ft) = Width × Length × Depth × Soil Storage Capacity / 43,560
Treatment Depth (in) = 12 × Width × Depth × Soil Storage Capacity / (Width + Width of Area Feeding it)

Both are strips that the runoff crosses as sheet flow, so the storage and the area are both per foot of strip length: the soil storage of the strip, spread over the strip plus the area that drains across it. Set to Detention + Plants they use the buffer tables instead of the retention curves. Worksheets: Vegetated Buffer, Vegetated Filter Strip.

Applicant’s Handbook reference

Appendix O, Table 1 (BMP Efficiencies), Green Stormwater Infrastructure Efforts: Vegetated Natural Buffers and Vegetated filter strip use “appropriate retention or detention calculation for volume captured”; BMPFast’s Retention setting does this with the soil storage. The buffer tables of the Detention + Plants setting are not from the handbook.

Source reference

FDEP and the water management districts (2010). Stormwater Quality Applicant’s Handbook: Design Requirements for Stormwater Treatment Systems in Florida, March 2010 draft (not adopted), Section 10.3 (the draft, not adopted: PDF, 16 MB): a vegetated natural buffer’s load reduction is read from the dry retention tables for the volume it infiltrates; the Treatment Depth equation is BMPFast’s.

BMPs that use the curves for capture only

The Surface Discharge Filter is not a retention BMP, but it reads its Hydraulic Capture from the same curves. Its Treatment Depth (0-4 in) is entered on the worksheet, or calculated by its Sizing form from the filter area and the media’s rate. The water it captures is filtered and discharged, so its removal is the capture times the media’s reduction, not the capture. See Surface Discharge Filter.

Retention BMPs in series

When the BMPs at the head of a series are all retention BMPs, BMPFast treats them as one system. Their Treatment Depths are added, and the sum, the Equivalent Treatment Depth, is read on the retention curves once.

Equivalent Treatment Depth (in) = sum of the Treatment Depths of the retention BMPs at the head of the series
Equivalent Treatment Efficiency (%) = retention curves (Equivalent Treatment Depth, Non-DCIA CN, DCIA %, zone)

What the series does after them is on BMPs in Series.

Applicant’s Handbook reference

Section 9.5.1 Treatment Train Nutrient Reduction (Equation 9-5): Equation 9-5 assumes each BMP acts independently; where a downstream unit’s efficiency depends on the upstream one, “the designer should consider the use of another methodology”. BMPFast differs from Equation 9-5 here on purpose: retention BMPs in series take the same runoff, so their depths are added and read once, instead of their removals being chained.

Source reference

BMPFast method (MultipleBMP.CalculateEquivalentRetentionDepth; retention-led series of every kind, Ron, 2026-10-01): retention BMPs at the head of a series, or retention BMPs in a routed strand, are one system: their Treatment Depths are added and the removal is read once from the retention tables.

FDEP and the water management districts (2010). Stormwater Quality Applicant’s Handbook: Design Requirements for Stormwater Treatment Systems in Florida, March 2010 draft (not adopted), Section 22.3 Dry Retention In Series, Table 22.3-2, notes 2 and 3 (the draft, not adopted: PDF, 16 MB): in its worked example the downstream basin’s efficiency is read from the dry retention tables at the sum of the two basins’ retention depths (2 in = 1.00 + 1.00 in; 1.89 in = 1.00 + 0.89 in), and the downstream basin is credited with the difference from the upstream basin’s efficiency; BMPFast’s Equivalent Treatment Depth adds the depths in the same way.

Retention BMPs in the routing

When other catchments route their runoff into a catchment whose BMP is a retention BMP, the BMP treats all of that runoff. Its Treatment Volume is then spread over the whole area that drains to it, with the area-weighted average Non-DCIA CN and DCIA percent of those catchments:

Treatment Depth (in) = 12 × Treatment Volume (ac-ft) / total area draining to it (ac)
Capture (%) = retention curves (Treatment Depth, average Non-DCIA CN, average DCIA %, zone)

This applies to Retention (its Provided Retention Volume), Exfiltration, Tree Well, Swale and the Vegetated Natural Buffer and Filter Strip set to Retention: each keeps the Treatment Volume it calculated. The same storage over a larger area gives a smaller depth and a lower capture. A Tree Well or buffer treats upstream runoff only when its catchment is set to treat it on the Routing screen; otherwise, like any catchment set to bypass upstream runoff, it treats only its own. See Routing.

Source reference

BMPFast method (ComplexRouting.cs): spreading a routed retention BMP’s Treatment Volume over all the area draining to it, with the area-weighted curve number and DCIA, is BMPFast’s own method.

Swale and buffers receiving runoff from upstream (BMPFast 2)

Decided (Ron Eaglin, October 19, 2026). A retention basin, exfiltration trench or tree well holds a fixed volume, so when runoff from upstream catchments reaches it, its Treatment Volume is spread over all the area draining to it (above). A swale and a buffer hold no single volume, so BMPFast 2 treats them by how they work:

Swale: recalculated with the added flow. The upstream runoff is turned into an equivalent rainfall excess area and added to the swale’s own; the swale’s flow, Manning depth of flow, wetted perimeter, infiltration and swale-block storage are calculated again with it. The Treatment Depth is over the whole excess area, and the removal is the retention curves at that depth with the area-weighted Non-DCIA CN and DCIA of all the area draining to the swale, on all the load that reaches it.

A up (ac) = upstream runoff (ac-ft/yr) × 12 / mean annual rainfall (in)
A (ac) = the swale's own rainfall excess area + A up
Flow in swale Q (cfs) = A × rainfall intensity (zone); depth of flow d from Manning; wetted perimeter P
Infiltrated depth (in) = [L × infiltration rate × P / (12 × 3600)] × 6000 × 12 / (A × 43560)
Block depth (in) = 12 × swale block storage / (A × 43560)
Treatment Depth (in) = min(4, infiltrated depth + block depth)
Removal (%) = retention curves (Treatment Depth, area-weighted Non-DCIA CN and DCIA %, zone), on all the load reaching the swale

Worked example (the sample project example problem 1 swale ground water discharge, Zone 1, mean annual rainfall 60 in: an 871.2 ft swale, infiltration rate 2.5 in/hr, its own rainfall excess area 0.600 ac; an untreated 1.2 ac catchment upstream sends it 3.588 ac-ft/yr):

A up = 3.588 × 12 / 60 = 0.718 ac;   A = 0.600 + 0.718 = 1.318 ac
Q = 1.318 × 0.1626 = 0.214 cfs; d = 0.375 ft; P = 3.827 ft
Infiltrated depth = [871.2 × 2.5 × 3.827 / 43200] × 6000 × 12 / (1.318 × 43560) = 0.242 in (no swale blocks)
Removal = retention curves (0.242 in, CN 85, DCIA 60 %, Zone 1) = 27.5 % of the 11.06 kg/yr TN reaching it; 8.02 kg/yr leaves
BMPFast (v1), its volume spread over the area instead: 0.099 in, 11.2 %, 9.82 kg/yr leaves

A run of retention catchments with such a swale below its top is calculated catchment by catchment, so the swale sees the flow it receives. The routing report notes each swale calculated this way.

Vegetated Natural Buffer and Vegetated Filter Strip: upstream runoff goes by. A buffer takes sheet flow from its own feeding width, not a whole upstream catchment, so in BMPFast 2 it always lets the runoff from upstream go by, untreated, to where its catchment drains, as rainwater harvesting and greenroof do; it treats its own catchment’s runoff only. On the Catchment Routing the choice “Runoff from upstream catchments” is locked for a buffer, saying why. BMPFast (v1) lets a buffer treat it once confirmed, spreading its depth like a basin.

Sample problems

Worked problems solved in BMPFast, each with every input, the steps with screen captures, the program’s results, a hand check and the project file to download. Captures are for demonstration only. All of them: BMPFast sample problems.

Help home · List of every help page · This page on bmpfast.com · Sample problems